Nylon 6/6 Round Rod, White, 1/8" OD, 72" Length

Nylon 6/6 Round Rod, White, 1/8" OD, 72" Length Reviews

Other Picture

Nylon 6/6 Round Rod, White, 1/8" OD, 72" Length Feature

• Heat Deflection Temperature Under Load is 200 F
• Resists Common Solvents, Esters, Ketones, Alkali's and Dilute Acid
• Tough and Impact Resistant
• Low Coefficient of Friction
• Easily Machined

Nylon 6/6 Rods and Sheet are typically used as material for insulators, shaft bearings and bushings, wear strips, hinges, gears, and general fixturing. Heat deflection temperature at 264 PSI: 200F (93C). Color: Natural.A tough general purpose plastic with outstanding resistance to organic chemicals, acids and alkalis, Nylon 6/6 wears well against other surfaces and has a low coefficient of friction. It is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications, (up to 10 percent ) which should be taken into account with its use.

Visit Store Now !!

Detail Products

• PTFE Round Rod, White, 3/16" OD, 36" Length
• Acetal Round Rod, Black, 3/4" OD, 36" Length

Detail Reviews

Ultem 2300 Round Rod, Beige, 3/4" OD, 36" Length

Ultem 2300 Round Rod, Beige, 3/4" OD, 36" Length Reviews

Other Picture

Ultem 2300 Round Rod, Beige, 3/4" OD, 36" Length Feature

• PEI will withstand continuous temperature of 390 F under load.
• Is rated UL 94 VO and is generally accepted by the FAA for aircraft interiors
• PEI has found use in the Medical Device Market because of its heat and radiation resistance
• It is prone to stress cracking in chlorinated solvents.
• It is soluble in partially halogenated solvents but resistant to alcohols, acids and hydrocarbon solvents.

Polyetherimide (PEI) is an amorphous, amber-to-transparent thermoplastic with similar characteristics to PEEK's. Relative to PEEK, it is cheaper, but less temperature-resistant, and lower in impact strength. It is prone to stress cracking in chlorinated solvents. It is available under the tradename Ultem, a registered trademark of General Electric, the principal developer and manufacturer. PEI will withstand continuous temperature of 390 F under load and is rated UL 94 VO and is generally accepted by the FAA for aircraft interiors. It is soluble in partially halogenated solvents but resistant to alcohols, acids and hydrocarbon solvents. PEI has found use in the Medical Device Market because of its heat and radiation resistance, hydrolytic stability, and transparency. In the electronics field it is used in lamp sockets, and printed circuit board substrates.

Visit Store Now !!

Detail Products

Detail Reviews

ABS Round Rod, Natural Beige, 1" OD, 36" L

ABS Round Rod, Natural Beige, 1" OD, 36" L Reviews

Other Picture

ABS Round Rod, Natural Beige, 1" OD, 36" L Feature

• Good Chemical Resistance
• Hard Surface
• Easily Machined
• Good for Vacuum Forming
• Good Impact Resistance

General purpose grade ABS combines heat stability, chemical resistance and surface hardness of Acrylonitrile with the toughness and impact resistance of Butadiene and the rigidity and machineability of Styrene...to give you ABS with easy formability and high gloss. Good for vacuum forming, with a normal forming temperature at 295F (146C) - Rockwell Hardness R-105. Color: Natural (Beige). Other grades: flame retardant, high heat, low gloss, medium impact.

Visit Store Now !!

Detail Products

• High Impact Styrene Sheet, White, 0.02" Thick, 24" Width, 24" Length
• HDPE (High Density Polyethylene) Round Rod, White, 1" OD, 12" Length
• ABS Textured Plastic Sheet 1/8 Thick x 12 x 24
• ABS Textured Plastic Sheet 3/32 Thick x 12 x 24

Detail Reviews

Kynar 740 PVDF Round Rod, USP-CLASS-VI, White, 3/4" OD, 48" Length

Kynar 740 PVDF Round Rod, USP-CLASS-VI, White, 3/4" OD, 48" Length Reviews

Other Picture

Kynar 740 PVDF Round Rod, USP-CLASS-VI, White, 3/4" OD, 48" Length Feature

• USP Class VI
• Continuous Operating Temperature 280 F
• UL 2360 Class II
• Chemically Inert
• Excellent Weatherability and UV Resistance

PVDF (polyvinylidene fluoride) is a flouroplastic in the fluorohydrocarbon family. The fully fluorinated PTFE is more chemically inert and thermally stable than the partially fluorinated PVDF; however PVDF has superior mechanical properties. Tensile strength is 7000 psi and the continuous operating temperature is 280F. Kynar 740 offers excellent chemical and corrosion resistance at both ambient and elevated temperatures. Rigidity and creep resistance are also superior to PTFE. Hardness is 77 Shore D. Color is Natural Beige. Easily machined, drilled and sawed. Excellent weather ability and UV resistant. Meets the following criteria: USP Class VI , UL 2360 Class II , Flammability Rating-UL 94 (V-0) ,FM 4910 Listed.

Visit Store Now !!

Detail Products

• Acetal Round Rod, White, 1/4" OD, 36" Length

Detail Reviews

Nylatron GS Round Rod, Black, 1/2" OD, 48" Length

Nylatron GS Round Rod, Black, 1/2" OD, 48" Length Reviews

Other Picture

Nylatron GS Round Rod, Black, 1/2" OD, 48" Length Feature

• Excellent Bushing and Bearing Material
• 1/8 the Weight of Bronze
• Corrosion Resistant
• Easily Maintained
• Easily Fabricated

Nylatron GS Nylon 6/6 is a molybdenum disulphide (MoS2) filled nylon offering improved strength and rigidity. It exhibits excellent wear and abrasion resistance and is 1/8 the weight of bronze making it an excellent replacement for metal bushings. It is easier to fabricate and maintain than metal.

Visit Store Now !!

Detail Products

• UHMW (Ultra High Molecular Weight) Polyethlylene Round Rod, White, 1" OD, 48" Length
• Acetal Round Rod, Black, 3/4" OD, 36" Length
• Nylon Molybdenum Round Rod, 1" OD, 36" Length
• 6 Inch LCD Digital Caliper with Extra Battery and Case
• Aluminum 6061-T6511 Round Rod, 2.5" OD, 36" Length

Detail Reviews

Rulon J Round Rod, Gold, 1" OD, 3" Length

Rulon J Round Rod, Gold, 1" OD, 3" Length Reviews

Other Picture

Rulon J Round Rod, Gold, 1" OD, 3" Length Feature

• Low Coefficient of Friction
• Use for bearing surface on soft metals
• Low moisture absorption, and excellent hydrolysis resistance
• Good choice for inaccessible bearing surfaces
• No lubrication required

Rulon-J Rod is made from an all-polymeric, PTFE compound that offers low coefficient of friction (0.05 to 0.20 depending upon temperature and load), and a hardness of 60 on Shore D Scale with 0 percent water absorption. The material was expressly developed to run against soft materials such as Brass, Type 316 Stainless Steel, Aluminum, Zinc and plastics, and other materials which are worn rapidly by existing filled PTFE compounds. Check chemical resistance before using in a harsh acid/alkali environment.NOTE: Not recommended for use with Nitric Acid or Ammonium Hydroxide. Should not be used with Sodium or Potassium Hydroxide above room temperature.

Visit Store Now !!

Detail Products

Detail Reviews

Torlon 4203 Round Rod, Brown, 5/8" OD, 6" Length

Torlon 4203 Round Rod, Brown, 5/8" OD, 6" Length Reviews

Other Picture

Torlon 4203 Round Rod, Brown, 5/8" OD, 6" Length Feature

• Temperature resistance from cryogenic to 500 F
• Melt Processable
• Excellent Chemical Resistance
• High Strength
• UL 94 Rated

Polyamide Imide (PAI) is a thermoplastic amorphous polymer that has exceptional mechanical, thermal, and chemical resistant properties. It is in the league of "Superpolymers" exhibiting temperature resistance from cryogenic to 500 F. This unique material combines properties from both polyamides and polyimides such as high strength, melt processability and it is inherently flame retardant. UL 94 ratings generally allow for FAA Aircraft Interiors due to very low smoke on ignition. Generally un affected by aliphatic and aromatic hydrocarbons, acids, bases and halogenated solvents. Applications include engine and generator components, hydraulic bushings and seals, and mechanical parts for electronics and business machines.

Visit Store Now !!

Detail Products

Detail Reviews

Turcite X ETFE Round Rod, Red, 3/4" OD, 12" Length

Turcite X ETFE Round Rod, Red, 3/4" OD, 12" Length Reviews

Other Picture

Turcite X ETFE Round Rod, Red, 3/4" OD, 12" Length Feature

• Load Bearing
• Minimally Hygroscopic
• Maximum Continuous Temperature 180 F
• Low Thermal Expansion
• Easily Fabricated

Turcite X is a fluoropolymer based material with proprietary additives for enhanced performance. It excels in low load and high speed applications, and can be easily machined. It has minimal hygroscopic characteristics and possesses low thermal expansion properties, resulting in a structurally stable material. Its maximum continuous service temperature is also 180 F (80 C). Turcite X has lower friction properties than Turcite A. Typical applications include bearings, bushings and slides. It is lubricious, similar to PTFE but has more back bone.

Visit Store Now !!

Detail Products

Detail Reviews

UHMW (Ultra High Molecular Weight) Polyethlylene Round Rod, White, 3/8" OD, 48" Length

UHMW (Ultra High Molecular Weight) Polyethlylene Round Rod, White, 3/8" OD, 48" Length Reviews

Other Picture

UHMW (Ultra High Molecular Weight) Polyethlylene Round Rod, White, 3/8" OD, 48" Length Feature

• Low Coefficient of Friction
• Very High Impact Strength
• Excellent Abrasion Resistance
• Self Lubricating
• Highly Resistant to Corrosives

Ultra high molecular weight polyethylene (UHMWPE), also known as high-modulus polyethylene (HMPE) or high-performance polyethylene (HPPE), is a thermoplastic. It has extremely long chains, with molecular weight numbering in the millions, usually between 2 and 6 million. The longer chain serves to transfer load more effectively to the polymer backbone by strengthening intermolecular interactions. This results in a very tough material, with the highest impact strength of any thermoplastic presently made. It is highly resistant to corrosive chemicals, with exception of oxidizing acids. It has extremely low moisture absorption, has a very low coefficient of friction, is self-lubricating, and is highly resistant to abrasion (15 times more resistant to abrasion than carbon steel). Its coefficient of friction is significantly lower than that of nylon and acetal, and is comparable to that of PTFE, sometimes none as the poor mansTeflon, but UHMWPE has better abrasion resistance than Teflon. It is odorless, tasteless, and nontoxic

Visit Store Now !!

Detail Products

• UHMW (Ultra High Molecular Weight) Polyethlylene Sheet, White, 1/8" Thick, 12" Width, 24" Length
• HDPE (High Density Polyethylene) Round Rod, White, 3/8" OD, 60" Length
• Nylatron GS Round Rod, Black, 1" OD, 36" Length
• Acetal Round Rod, Black, 3/4" OD, 36" Length
• HDPE (High Density Polyethylene) Sheet, White, 0.25" Thick, 12" Width, 24" Length

Detail Reviews

Nylon 6/6 Round Rod, White, 1" OD, 36" Length

Nylon 6/6 Round Rod, White, 1" OD, 36" Length Reviews

Other Picture

Nylon 6/6 Round Rod, White, 1" OD, 36" Length Feature

• Heat Deflection Temperature Under Load is 200 F
• Resists Common Solvents, Esters, Ketones, Alkali's and Dilute Acid
• Tough and Impact Resistant
• Low Coefficient of Friction
• Easily Machined

Nylon 6/6 Rods and Sheet are typically used as material for insulators, shaft bearings and bushings, wear strips, hinges, gears, and general fixturing. Heat deflection temperature at 264 PSI: 200F (93C). Color: Natural.A tough general purpose plastic with outstanding resistance to organic chemicals, acids and alkalis, Nylon 6/6 wears well against other surfaces and has a low coefficient of friction. It is readily machinable and may be milled, turned and cut with conventional machine tools. It does exhibit some dimensional swelling in wet applications, (up to 10 percent ) which should be taken into account with its use.

Visit Store Now !!

Detail Products

Detail Reviews

PEEK Round Rod, Tan, 3/4" OD, 6" Length

PEEK Round Rod, Tan, 3/4" OD, 6" Length Reviews

Other Picture

PEEK Round Rod, Tan, 3/4" OD, 6" Length Feature

• Glass transition temperature of approx. 500 F
• Superior Chemical Resistance
• Low moisture absorption, and excellent hydrolysis resistance
• Used extensively in medical applications, chemical processing and electronics industries
• Sterilizable By All Known Conventional Methods

Valued for its ability to withstand high temperatures, outstanding chemical resistance (organic, inorganic solvents, aqueous reagents), and good mechanical strength, PEEK (Polyetheretherketone) is a highly crystalline thermoplastic that maintains its properties under an extreme range of conditions. Used extensively in medical applications, chemical processing and electronics industries, this material offers good wear resistance, low moisture absorption, and excellent hydrolysis resistance. Repeated sterilization by all known methods has no effect on PEEK devices. Color: Putty

Visit Store Now !!

Detail Products

Detail Reviews

Teflon FEP Round Rod, White, 1" OD, 36" Length

Teflon FEP Round Rod, White, 1" OD, 36" Length Reviews

Other Picture

Teflon FEP Round Rod, White, 1" OD, 36" Length Feature

• Temperature Range -348 to 400 F
• Extreme Chemical Resistance
• Lowest critical surface energy of all plastics
• Lowest Refractive Index of All Plastics
• Extremely low dielectric constant and dissipation factor

Teflon FEP Rod has excellent chemical, thermal, and electrical stability. It retains a high percentage of its useful properties from cryogenic to elevated temperatures -348 F to 400 F. It has the lowest critical surface energy of all plastics, which makes it an excellent water and oil repellent for non-stick and mold release. Teflon FEP has an extremely low dielectric constant and dissipation factor. Excellent resistance to UV, Ozone, and has the lowest refractive index of all plastics. Typical applications include electronic bobbins, piping material for high temperature use, spring actuated seals, gaskets, packing and valve seats.

Visit Store Now !!

Detail Products

• PTFE Round Rod, White, 1/2" OD, 24" Length
• Teflon PTFE Sheet, White, 1/4" Thick, 12" Width, 12" Length

Detail Reviews

PTFE Round Rod, White, 1-1/2" OD, 36" Length

PTFE Round Rod, White, 1-1/2" OD, 36" Length Reviews

Other Picture

PTFE Round Rod, White, 1-1/2" OD, 36" Length Feature

• Rod Form
• Max Temp 400 F
• Very Low Coefficient of Friction
• Extremely Low Dielectric Constant
• UV and Ozone Resistant

PTFE (Polytetrafluoroethylene Teflon) has established itself as a tough, durable polymer, possessing a unique combination of electrical, chemical, mechanical and thermal properties unmatched by any other single substance. Maximum operating temperature 350 to 400F (176 to 204C). This material should not be heated to temperatures above 752F (400C).

Visit Store Now !!

Detail Products

• Acetal Round Rod, Black, 3/4" OD, 36" Length
• PTFE Sheet, White, 0.015" Thick, 12" Width, 12" Length
• PEEK Round Rod, Tan, 1/2" OD, 12" Length
• Acetal Round Rod, White, 1-1/2" OD, 12" Length
• Brass 360-H02 Round Rod, ASTM B16, 1/8" OD, 72" Length

Detail Reviews